CALL: 800.359.0567

Local: 828.277.6601

8AM-5PM EST/GMT-5 | Mon-Fri

  • Honda Motorcycle Parts | Honda ATV Parts
  • Yamaha ATV Parts | Yamaha Motorcycle Parts
  • Polaris ATV Parts | Polaris Accessories
  • Kawasaki ATV Parts | Kawasaki Motorcycle Parts
  • Suzuki Motorcycle Parts | Suzuki ATV Parts

Starter Motors Cyclepedia

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

Rebuilding Starter Motors

It is possible to rebuild nearly every starter motor in use on a motorcycle or ATV, but before you start it’s best to do a little research. Checking at your local shop, you may find that a starter motor for your machine is fairly inexpensive. If that’s the case, it is hardly worth the effort of taking apart an ailing starter motor even to diagnose what may have gone wrong. If your replacement starter motor is on the pricey side, look deeper to see what replacement parts are available. Often you can replace the brushes, but if you have a bad armature and can’t get one you’ll be replacing the whole starter anyhow. The same situation exists with the end cap bearings—many machines list new end caps unavailable as a replacement part.

The best advice we can give is to use this chapter as a diagnostic tool. If your $200 starter motor only needs a set of $35 brushes to get going again, you can save some money doing a rebuild.

All starter motors follow a similar design, with a few differences according to use and individual brands. Here we will show you how to take the motor apart and troubleshoot problems, and how to get the starter back together and serviceable again. Individual specifications, such as armature coil resistance, brush length and commutator diameter will vary from each different starter motor, so use the specifications for your particular machine as the final guide when you’re examining the motor.

Disassembly

Starter Body

CBR_07_459

Look for a set of marks, or make a set of marks on the starter body to aid in reassembly.

AN650_575

Remove the O-ring and discard it. Try to turn the starter motor armature shaft with your hand. It should turn with a small amount of resistance. If it doesn’t turn at all or is very hard to turn, the starter motor will need to be replaced or rebuilt.

AN650_573

Remove the terminal nut with the proper size socket.

AN650_574

Keep track of the nut and any combination of insulators and washers that may come off the terminal.

AN650_576

Remove the two bolts holding the starter motor together. The bolts commonly have a 7 mm head.

AN650_577

Do not lose the o-ring on the bolt shaft, and plan to use a new one upon reassembly.

AN650_578

Remove the front cover from the starter motor.

AN650_579

Carefully remove the o-ring from the front cover, and use a new one upon reassembly.

AN650_580

Check the condition of the bearing in the end cap. If it is obviously damaged, or if it turns roughly or feels notchy, you will need to replace the bearing or the entire end cap, depending on what is available for your vehicle in spare parts.

AN650_581

Remove the rear cover from the starter body. In some cases the bearing comes out with the armature shaft as above, and in others the bearing is fixed in the case. Either way, check the condition of the bearing and plan to replace it or the cap if it is bad.

AN650_582

Remove the armature from the starter body.

Armature Inspection

GSX600FKatana2006_1748

Inspect the armature for abnormal wear or damage.

SV650_414

Keep track of any shims on the commutator end of the armature, and return them to their proper place when finished.

GSX600FKatana2006_1741 copy

Measure the diameter of the commutator and compare your measurement to the service limit specified for your bike. If the commutator is worn past the service limit, replace the armature.

GSX600FKatana2006_1744

Using a digital multimeter set to measure resistance (Ω X 1), touch one meter lead to any one commutator strip and touch the other meter lead to all of the other commutator strips one by one. Polarity of the meter leads does not matter. There should be continuity for all of the readings, if any readings show no continuity there is an open circuit and the armature must be replaced.

GSX600FKatana2006_1745

Next, touch one meter lead to the steel shaft of the armature and touch the other meter lead to each commutator strip. Polarity of the meter leads doesn’t matter. There should be no continuity. Continuity between the shaft and the commutator strip indicates a short in the windings, and the armature must be replaced.

GSX600FKatana2006_1742

On most motors, the commutator can be cleaned up with a few gentle strokes of some 400 grit emery paper and cleaning with a dry shop rag.

GSX600FKatana2006_1743

The other critical item in motor health is referred to as “mica depth” or “undercut,” which is the offset between the commutator strip and the underlying mica insulator. This strip, as shown above, should be cleaned out to a specified depth, usually somewhere between 0.5 mm and 1.5 mm. The mica undercut can be cleaned out with a razor blade, small screwdriver or hacksaw blade, just as long as the tool fits the groove it’s cleaning.

CBR_07_455

Honda’s unique CBR600RR starter motor with a flat commutator is tested in exactly the same way. Honda does not recommend using emery paper on the commutator, nor is it recommended that the mica undercut be cleaned out.

Brush Holder

AN650_584

The most common brush holders are mounted on a plate in the rear cover. Remove them by carefully removing the terminal post from the body, along with the brush holder.

AN650_586

This brush holder uses two brushes.

GSX600FKatana2006_1731

Here is a four brush holder that is held in by a pair of Phillips head screws.

CBR_07_437

Here is the four brush holder from a Honda CBR600RR that contacts the armature head-on rather than around the circumference. This design makes reassembling the motor body a much simpler process.

CRF250X_300

Remove the brushes by pulling back the spring and working the brush out the back of its holder.

CRF250X_301

Measure the remaining working length of the brush and compare it to the specifications applicable to your machine, and replace as necessary. Of course, if you’ve torn the starter motor down to this point, your time would be better spent by putting new brushes in rather than worrying a few more millimeters of life out of the old ones.

Assembly

GSX600FKatana2006_1730

Insert the armature into the motor body.

GSX600FKatana2006_1729

Insert the back cap onto the body, with a new o-ring in place. This can be a difficult task, since the commutator has to be fit between the spring loaded brushes. Note the position of the brushes in this photo—spread apart at the top to allow the commutator to fit.

GSX600FKatana2006_1728

Put a new o-ring onto the front cover, and grease the bear and seal lips.

GSX600FKatana2006_1727

Install any shims and lock rings into the cover.

GSX600FKatana2006_1726

 

Match the alignment marks and put the front cover onto the body.

GSX600FKatana2006_1725

Put a new o-ring onto each of the bolts and slide them into position. Tighten the bolts to the specifications given for your machine.

GSX600FKatana2006_1723

Fit a new o-ring onto the front of the motor with a light coat of grease, and it is ready to be installed.

Online Service Manuals

http://www.cyclepedia.com

Repair Your ATV, Motorcycle or Scooter Yourself

Concerned about up-time? Cyclepedia.com is your online source for motorcycle repair information. We publish full color, online manuals to help you save time and money servicing ATVs, motorcycles, scooters and side by sides. Every Cyclepedia subscription includes free tech support. Need help with your ATV, Motorcycle, Scooter or Side by Side? Give us a call at 828-645-0017 between 9am – 5pm Eastern Standard Time to talk with a member of our support staff.

Browse the Cyclepedia Catalog of Online Motorcycle Repair Manuals

Dealers may access our complete library of manuals, plus unlimited specification look-ups through CYCLEPEDIA PRO – now just $99.95 a year or $19.95 a month!

Honda Motorcycle Parts | Honda ATV Parts Yamaha ATV Parts | Yamaha Motorcycle Parts Polaris ATV Parts | Polaris Accessories Kawasaki ATV Parts | Kawasaki Motorcycle Parts Suzuki Motorcycle Parts | Suzuki ATV Parts
We proudly accept
PayPal Logo

MRCycles
774 Hendersonville Road
Asheville NC 28803
ph: 800.359.0567